Home - Knowledge - Details

ASTM A213 TP304 Seamless Boiler Tube: Specs & U-Bends

1. Standard Scope: ASTM A213 / ASME SA213 TP304

ASTM A213/A213M and ASME SA213/SA213M specify seamless ferritic and austenitic steel boiler tubes, superheater tubes and heat exchanger tubes. Grade TP304 (UNS S30400) is the workhorse austenitic grade for moderate-temperature, moderately corrosive service. Although designed for high-temperature boiler duty, TP304 seamless tube is equally suitable at ambient temperature and under normal atmospheric conditions, which makes it a flexible stock item for heat exchangers, condensers and process piping.

2. Chemical Composition: TP304 vs TP304L

Element TP304, % TP304L, %
Carbon, C 0.08 max 0.035 max
Manganese, Mn 2.00 max 2.00 max
Phosphorus, P 0.045 max 0.045 max
Sulfur, S 0.030 max 0.030 max
Silicon, Si 1.00 max 1.00 max
Chromium, Cr 18.0-20.0 18.0-20.0
Nickel, Ni 8.0-11.0 8.0-12.0

For welded assemblies where the tube is exposed to temperatures in the sensitization range (430-870 deg C), specify TP304L to avoid intergranular corrosion. For long-term elevated-temperature strength, grades TP304H or TP321H are the correct choice instead of TP304.

3. Mechanical Properties and Heat Treatment

Property TP304 requirement
Tensile strength, min 515 MPa
Yield point (0.2%), min 205 MPa
Elongation, min 35%
Hardness, max 90 HRB
Solution treatment 1040 deg C minimum, rapid cooling

Tubes are supplied solution annealed and pickled; the pickling and passivation step removes mill scale and restores the protective chromium oxide film. Surface finishing options such as wire drawing and polishing are available on request.

4. Manufacturing Process and Available Sizes

The primary manufacturing route for ASTM A213 TP304 seamless tube is cold rolling or cold drawing of a pierced hollow, followed by heat treatment and pickling. Each stage is recorded under a documented quality system so that the mill test certificate (MTC) can be issued as EN 10204 type 3.1.

Outer diameters: 1.58 mm to 108 mm (imperial and metric); special sizes on request

Wall thickness: SCH 5 to SCH 160 and XXS series

Delivery forms: straight lengths, coils, and U-bends up to 30 metres total developed length

Ends: plain, beveled or threaded

Surfaces: AP (annealed and pickled), BA (bright annealed), 2B, No.1, 400G-600G, mirror polish

U-bending is performed with mandrel tooling to control ovality and wall thinning; bent tubes are supplied with the bend zone solution annealed or stress relieved as required by the design code.

5. Quality Assurance, Testing and Applications

Every tube is checked before despatch with a combination of tests appropriate to the standard:

Dimensional inspection (OD, wall thickness, straightness, length)

Surface inspection

PMI (positive material identification) on chromium and nickel

Eddy current testing for surface and sub-surface defects

Hydrostatic testing for pressure integrity

Tension and flattening tests per ASTM A1016

For export boiler and heat exchanger projects, request the EN 10204 type 3.1 mill certificate with heat number, chemical analysis and mechanical results, and agree on third-party inspection when the contract requires it.

Boiler tubes and superheater tubes in industrial and power boilers

Heat exchanger and condenser tubes in chemical, food and pharmaceutical plants

Process instrumentation tubing and hydraulic lines

Sanitary and general fluid handling where corrosion resistance and clean bore are required

Packaging for export is waterproof paper plus steel strapping, suitable for sea freight, or customized to the customer's specification.

6. FAQ

What is the difference between TP304 and TP304L in boiler tube service?

TP304L limits carbon to 0.035% maximum, preventing sensitization during welding so the tube keeps corrosion resistance without post-weld heat treatment. TP304 is preferred where slightly higher elevated-temperature strength is needed and the tube is not welded.

Can ASTM A213 TP304 tube be supplied as U-bends?

Yes. U-bend tubes are manufactured with mandrel bending, and straight or U-bend tubes can be supplied in developed lengths up to 30 metres. Specify the bend radius, leg lengths and whether the bend zone must be stress relieved.

What surface finish is standard for boiler tubes?

The standard delivery condition is annealed and pickled (AP). Bright annealed (BA), wire-drawn and polished finishes are available for sanitary or high-cleanliness applications.

What is the maximum operating temperature of TP304 tube?

For oxidation resistance, continuous service is practical up to about 870 deg C, but for pressure parts the allowable stress drops sharply above 540 deg C, and creep strength is poor compared with stabilized grades. For long-life superheater duty above 600 deg C, select TP321H or TP347H instead.

Which tests are included in the mill certificate?

Per ASTM A213/A1016: tension, flattening, flaring (where applicable), hardness, hydrostatic or non-destructive electric test. Suppliers typically add eddy current and PMI; these should be stated explicitly in the purchase order.

Send Inquiry

You Might Also Like