Home - Knowledge - Details

Carriage Bolts: Application Fields, Standards and Selection

What a Carriage Bolt Is

A carriage bolt, also called a round head square neck bolt, is a fastener with a smooth domed head and a short square section beneath it. When the bolt is driven into a pre-bored hole in timber or a slotted steel section, the square neck bites into the material and locks against rotation, so the joint can be tightened from the nut side alone. That single feature is why carriage bolts dominate structural timber work, where access to the head is impossible once assembly starts.

The head is deliberately smooth and low profile, so nothing protrudes to snag clothing, cargo or equipment, and the bolt cannot be undone from the outside with ordinary tools.

Design Features That Drive Selection

Domed head. Provides a finished, snag-free surface and spreads load over the timber face.

Square neck. Grips the parent material to prevent rotation during tightening and to resist vibration loosening.

Coarse thread. Grips timber and softer substrates without stripping.

Full or part thread. Full-thread bodies clamp thin sections, while part-thread bodies suit thicker timber.

Bevelled or flat bearing face. The bevelled version seats into a countersunk hole for a flush fit.

Standards, Materials and Finishes

Metric carriage bolts are produced to DIN 603 or to the equivalent GB/T 12 dimensional standard, while imperial sizes follow ASME B18.5. Metric property classes are usually 4.8 or 8.8 under the ISO 898-1 system, and imperial bolts follow the SAE J429 grade structure. Stainless variants are made in A2 and A4 material to the ASTM F593 chemistry and mechanical requirements.

Item Typical option
Metric standard DIN 603, GB/T 12
Imperial standard ASME B18.5
Carbon steel classes 4.8, 8.8 (metric); Grade 2, Grade 5 (imperial)
Stainless grades A2 (304), A4 (316) to ASTM F593
Diameter range M5 to M20 metric; 1/4 in to 1 in imperial
Length range 40 mm to 200 mm typical
Coatings Zinc plating, zinc flake, hot-dip galvanised to ASTM A153

Hot-dip galvanising to ASTM A153 is the usual choice for outdoor timber structures, while zinc plating suits indoor assembly and stainless A2 or A4 is selected where washing, condensate or coastal air would corrode a coated carbon steel bolt.

Automotive and Transportation Applications

Vehicle body builders, trailer and truck manufacturers, and repair workshops use carriage bolts to fix chassis brackets, body panels, mudguards, floor sections and engine bay components. The square neck holds the bolt while the operator works single-handed underneath the vehicle, and the smooth head will not chafe wiring, hoses or load. In rail and container work the same behaviour simplifies panel fixing where only one face is accessible.

Construction, Infrastructure and Timber Engineering

In building and civil works, carriage bolts connect timber trusses, joists, pole frames, dock structures, pergolas and fencing, and they also fix steel sections, handrails, guardrails and mechanical equipment to concrete or masonry through drilled anchors. Because the bolt is loaded predominantly in shear and tension, selection is based on the clamping requirement, the substrate and the exposure class. Corrosion-resistant coatings or stainless steel are specified for bridges, jetties and other weather-exposed structures.

Furniture, Interiors and Agricultural Equipment

Furniture manufacture: chairs, benches, tables, bed frames and cabinets, where the domed head stays flush with the surface.

Shopfitting and interior fit-out: shelving, partitions and display units assembled on site.

Agricultural machinery: implements, trailers, feeding equipment and fencing systems exposed to mud and wash-down.

General industrial assembly: jigs, guards, pallets and crates that must be re-tightened in service.

For all of these fields the practical choice comes down to four variables: head and neck geometry to match the hole, property class or material grade to match the load, coating to match the environment, and thread length to match the thickness of the parts being clamped.

Frequently Asked Questions

Q: Why do carriage bolts have a square neck?
The square neck bites into timber or an anti-rotation slot and locks the bolt, so it can be tightened from the nut side without holding the head.

Q: Which standards cover carriage bolts?
Metric bolts follow DIN 603 or GB/T 12, imperial bolts follow ASME B18.5, and property class or material performance is defined by ISO 898-1, SAE J429 or ASTM F593 for stainless grades.

Q: Are carriage bolts suitable for steel structures?
They can be used where a square hole or slot is provided, but structural steel connections are more often made with hex bolts or structural bolts to the relevant bolting code.

Q: What sizes are available?
Common production covers M5 to M20 metric and 1/4 in to 1 in imperial, with lengths typically from 40 mm to 200 mm and longer sizes on request.

Q: Which coating should be chosen for outdoor use?
Hot-dip galvanising to ASTM A153 is standard for exposed timber and civil structures, while A2 or A4 stainless is preferred in coastal, wash-down or chemical atmospheres.

Q: How is the correct bolt length determined?
Add the thickness of the parts being clamped to the nut, washer and at least two exposed thread pitches, then round to the nearest stocked length.

Send Inquiry

You Might Also Like