304 Stainless Steel Composition: Full Element Breakdown
Leave a message
What Defines 304 Stainless Steel?
304 is the most widely used stainless steel in the world, and it is defined entirely by chemical composition. Two elements dominate: nickel, which determines corrosion resistance and value, and chromium, which forms the protective oxide film. The industry shorthand is 18-8 stainless steel: roughly 18% chromium and 8% nickel. However, a material can only be certified as 304 if every element meets the limits of the applicable product standard. A single out-of-range element disqualifies the material, even if chromium and nickel look correct.
Composition per Standard (wt %)
| Element | ASTM A276 (Bars & Shapes) | ASTM A240 (Plate, Sheet & Strip) | JIS G4305 (Cold-Rolled Sheet) | JIS G4303 (Bars) |
|---|---|---|---|---|
| Carbon (C) | ≤ 0.08 | ≤ 0.07 | ≤ 0.08 | ≤ 0.08 |
| Manganese (Mn) | ≤ 2.00 | ≤ 2.00 | ≤ 2.00 | ≤ 2.00 |
| Phosphorus (P) | ≤ 0.045 | ≤ 0.045 | ≤ 0.045 | ≤ 0.045 |
| Sulfur (S) | ≤ 0.030 | ≤ 0.030 | ≤ 0.030 | ≤ 0.030 |
| Silicon (Si) | ≤ 1.00 | ≤ 0.75 | ≤ 1.00 | ≤ 1.00 |
| Chromium (Cr) | 18.0 – 20.0 | 17.5 – 19.5 | 18.0 – 20.0 | 18.0 – 20.0 |
| Nickel (Ni) | 8.0 – 11.0 | 8.0 – 10.5 | 8.0 – 10.5 | 8.0 – 10.5 |
| Nitrogen (N) | - | ≤ 0.10 | - | - |
The limits differ slightly between standards because each addresses a different product form and manufacturing route, but the practical chemistry is the same. The low-carbon variant 304L (UNS S30403) caps carbon at 0.030% for welding-heavy fabrication.
Why Each Element Matters
Chromium (17.5–20%): forms the self-healing passive chromium oxide film; below about 10.5% a steel cannot be called stainless.
Nickel (8.0–11%): stabilizes the austenitic structure, providing toughness, formability and non-magnetic behavior; it is the most expensive element and drives grade value.
Carbon (≤ 0.07–0.08%): raises strength but can precipitate as chromium carbide at grain boundaries during welding; the low limit preserves corrosion resistance in the heat-affected zone.
Manganese (≤ 2.00%) and silicon (≤ 0.75–1.00%): deoxidizers that also improve hot workability.
Phosphorus and sulfur (≤ 0.045% / 0.030%): impurities controlled for hot cracking resistance and ductility.
Nitrogen (≤ 0.10–0.11%): strengthens the austenite and improves pitting resistance at low cost.
How Composition Affects Performance
With a correct 304 composition, the steel resists atmospheric corrosion, food acids, most organic and inorganic acids, and alkaline solutions. In boiling nitric acid up to 65% concentration, 304 shows strong resistance in laboratory tests. Because the austenitic structure is stabilized by nickel, annealed 304 is essentially non-magnetic; heavy cold work can induce slight magnetism. The grade cannot be hardened by heat treatment and is strengthened only by cold working.
Common Misconceptions
"Any steel with 18% chromium is 304." Nickel, carbon, sulfur and the rest must all be in range; one failed element disqualifies the heat.
"304 and 304L are identical." The carbon limit differs (0.08% vs 0.03%), and 304L is preferred where heavy welding could sensitize the material.
"Composition guarantees corrosion performance." Surface finish, contamination, chlorides and temperature all matter; composition is the necessary foundation, not the whole answer.
Frequently Asked Questions
What is the chemical composition of 304 stainless steel?
Approximately 17.5-20% chromium, 8.0-11% nickel, up to 0.08% carbon, 2% manganese, 0.75-1.0% silicon, 0.045% phosphorus and 0.030% sulfur, per ASTM A276/A240 and JIS G4303/G4305.
Why is 304 called 18-8 stainless steel?
Because its nominal composition is 18% chromium and 8% nickel, the two defining elements of the grade.
What is the difference between 304 and 304L?
304L caps carbon at 0.030% instead of 0.07-0.08%, which prevents sensitization during welding and keeps the weld zone corrosion-resistant.
Does 304 contain molybdenum?
No. Grades with 2-3% molybdenum belong to the 316 family; that is why 316 costs more and resists chlorides better.
Is 304 magnetic?
Annealed 304 is essentially non-magnetic; heavy cold working can make it slightly magnetic due to strain-induced martensite.
Which standard should I cite when ordering 304?
Cite the product form: ASTM A276 for bars, ASTM A240 for plate/sheet/strip, ASTM A312/A269 for pipe and tube, or JIS G4303/G4305 for SUS304 bars and sheet.







