310 vs 310S pipe for heat exchanger
Leave a message
When designing or upgrading a heat exchanger system for high-temperature or corrosive environments, choosing the right stainless steel grade is crucial. 310 and 310S stainless steel pipes are both excellent candidates due to their superior heat and oxidation resistance. However, there are key differences between them that can significantly affect performance, durability, and welding outcomes.
So, which is better for your heat exchanger – 310 or 310S? Let's dive in.
What standards apply to 310/310S heat exchanger pipes?
Common standards include ASTM A312 (seamless/welded pipe), ASTM A213 (boiler & heat exchanger tubes), and EN 10216-5.
What are the differences between 310 and 310S Stainless Steel Pipe?
| Grade | Key Feature |
|---|---|
| 310 | High carbon for intermittent high-temperature use |
| 310S | Low carbon for continuous high-temperature stability |
Stainless Steel 310/310S Tubes Equivalent Grades
| STANDARD | WERKSTOFF NR. | UNS | JIS | BS | GOST | AFNOR | EN |
| SS 310 | 1.4841 | S31000 | SUS 310 | 310S24 | 20Ch25N20S2 | - | X15CrNi25-20 |
| SS 310S | 1.4845 | S31008 | SUS 310S | 310S16 | 20Ch23N18 | - | X8CrNi25-21 |
SS 310/310S Heat Exchanger Tubes Chemical Composition
| Element | SS 310 | SS 310S |
| C | 0.015 max | 0.08 max |
| Mn | 2.0 max | 2.0 max |
| Si | 0.15 max | 1.00 max |
| P | 0.020 max | 0.045 max |
| S | 0.015 max | 0.030 max |
| Cr | 24.00 - 26.00 | 24.00 - 26.00 |
| Mo | 0.10 max | 0.75 max |
| Ni | 19.00 - 21.00 | 19.00 - 21.00 |
| Fe | 54.7 min | 53.095 min |
Stainless Steel 310/310S Condenser Tube Mechanical & Physical Properties
| Element | SS 310/310S |
| Density | 7.9 g/cm3 |
| Melting Point | 1402 °C (2555 °F) |
| Tensile Strength | Psi – 75000 , MPa – 515 |
| Yield Strength (0.2%Offset) | Psi – 30000 , MPa – 205 |
| Elongation |
40 % |
Heat Treatment:
310: Anneal at 1040–1120°C followed by rapid cooling.
310S: Stress relieve at 870–925°C for welded components.
Temperature Resistance:
310: Ideal for intermittent high temps (up to 1035°C).
310S: Best for continuous high temps (up to 1150°C).
Is 310S better than 310 for welding?
310S: No post-weld annealing required due to low carbon.
310: Requires post-weld heat treatment to restore corrosion resistance.
Cost:
310: Lower initial cost for cyclic heating applications.
310S: Higher cost but reduces long-term maintenance in sustained heat.
Fabrication Tips
Why Choose 310S Over 310 for Heat Exchanger Pipes?
The answer lies in welding and corrosion resistance.While both 310 and 310S offer similar thermal performance, 310S contains lower carbon, which minimizes the risk of intergranular corrosion in welded areas – a critical factor in heat exchanger fabrication. This makes 310S the preferred choice for pressure-bearing, welded tube sheets, U-bend tubes, and shell-side piping.
Use 310S pipe if your heat exchanger design involves:
1.Extensive welding
2.High-cycle thermal fatigue
3.Harsh oxidizing or slightly acidic steam
4.Pressurized media or condensate exposure
What is the maximum service temperature of 310S pipe in a heat exchanger?
Up to 1050–1100°C in oxidizing environments.
Need 310S Heat Exchanger Tubes with Guaranteed Performance?
At Gnee Steel, we supply high-quality 310/310S stainless steel pipes and tubes with full certification to ASTM A312, A213, EN 10216-5, and offer:
🔹 Seamless & welded pipes from OD 6mm to 610mm
🔹 Custom U-bend and coil configurations for exchangers
🔹 PMI, UT, hydrostatic test, and pickled finish
🔹 Global shipping and engineering support for projects
📩 Contact us today for technical datasheets, MTCs, or a competitive quote on 310S heat exchanger pipes!









