Non-Oriented vs Oriented Silicon Steel Sheet: Silicon Content, Process and Use
Leave a message
Non-oriented silicon steel sheet and oriented silicon steel sheet are both cold-rolled electrical steels made from iron-silicon alloys, and they are produced on similar equipment from similar melts. The relationship between them is best understood as one shared manufacturing platform that is split by silicon content, texture control and final use. One material carries magnetic flux equally in every direction of the sheet; the other is engineered so that flux travels easily in one direction only.
This article explains how the two sheets relate to each other in composition, process route, grain structure, magnetic behaviour and application, and where each one is the correct choice.
Silicon Content: Where the Two Sheets Separate
Both products are cold-rolled silicon steel sheet, but the alloy level differs from the start.
| Item | Cold-rolled non-oriented silicon steel sheet | Cold-rolled oriented silicon steel sheet |
|---|---|---|
| Silicon content | About 0.5-3.0 % | About 3.0 % and above |
| Carbon in the slab | Kept very low | Deliberately held near 0.03-0.05 % for inhibitor control, then removed |
| Grain arrangement | Disordered | Ordered, near Goss texture |
| Magnetic behaviour | Nearly isotropic | Strongly directional |
| Finished thickness | Commonly 0.35 mm and 0.50 mm | Commonly 0.28 mm, 0.30 mm and 0.35 mm |
| Typical end product | Motors, generators, compressors | Transformers and reactors |
Silicon is added for magnetics, not for strength. It raises the electrical resistivity of iron, which reduces eddy-current loss, and it lowers coercive force, hysteresis loss and magnetic ageing. Because silicon also makes the strip harder and more brittle, the upper limit in each product is set by how well the material can be cold rolled, punched and stacked.
Production Route: One Platform, Two Processes
Non-oriented silicon steel sheet has the shorter and less demanding route. A hot-rolled or continuously cast billet is rolled to a coil of about 2.3 mm.
Low-silicon grades: the hot-rolled coil is pickled and cold rolled in one pass to about 0.50 mm.
High-silicon grades: the hot-rolled strip is pickled, or normalised at 800-850 °C and then pickled, cold rolled to roughly 0.55 mm or 0.37 mm, annealed at about 850 °C in a hydrogen-nitrogen continuous furnace, and then given a light final reduction of 6-10 % to 0.50 mm or 0.35 mm.
That light final reduction is deliberate. A small cold reduction before the final anneal produces a coarser grain during annealing, and a coarser grain lowers iron loss.
Oriented silicon steel sheet adds texture control on top of the same sequence, which is why it is often described as a precision metallurgical product rather than a commodity strip:
The melt is aimed at a narrow carbon level, around 0.03-0.05 %, and alloyed with manganese and aluminium so that dispersed inhibitor phases such as manganese sulfide and aluminium nitride can form.
The slab is hot rolled and normalised so that coarse inhibitor particles dissolve and re-precipitate as fine particles at the right stage.
Cold rolling is carried out in two stages with an intermediate anneal, reaching the finished thickness of about 0.28-0.35 mm.
Decarburisation annealing removes carbon to a very low level and prepares the strip for secondary recrystallisation.
A high-temperature anneal develops the {110}<001> Goss texture, after which the inhibitor phases are purified away because they would otherwise harm the magnetics.
Both products then receive their final steps on the same type of line: a final anneal at about 850 °C in a continuous furnace using a hydrogen-nitrogen atmosphere, followed by an insulating film of phosphate and chromate type chemistry. The coating provides inter-laminar resistance in the finished core, and in oriented grades it also applies surface tension that refines the magnetic domains and reduces loss further.
Grain Structure and the Magnetic Result
The visible difference between the two sheets under a microscope is the grain arrangement. Oriented silicon steel has grains that are aligned in an orderly way, so that the easiest magnetisation axis of each grain points along the rolling direction. Non-oriented silicon steel has grains arranged in a disordered way, which is exactly what a rotating machine requires.
The consequences are easy to state in numbers:
In oriented strip, iron loss measured along the rolling direction is only about one third of the loss measured across it, and the permeability ratio between the two directions is roughly 6:1.
Compared with traditional hot-rolled silicon strip, the iron loss of oriented cold-rolled strip is about half, while its permeability is roughly 2.5 times higher.
Non-oriented strip has a higher saturation induction than oriented strip, which is one reason it suits motors, where high torque at high flux density matters.
This is why handling rules are so strict for oriented sheet. A badly positioned shear, a rough punch or a bending radius that damages the grain structure near the flux path can destroy the very property that justified the purchase. Non-oriented sheet tolerates forming very well by comparison.
Where Each Sheet Is Used
Generators and transformers place the same demands on electrical steel: low iron loss, good magnetisation characteristics and a high lamination or stacking factor. The two sheets simply meet those demands in different flux geometries.
| Application | Preferred sheet | Reason |
|---|---|---|
| Power and distribution transformer cores | Oriented silicon steel | Flux path is fixed and aligned with the rolling direction |
| Reactors and inductors | Oriented, with cut or stepped cores | Low loss in a single flux direction |
| Stators and rotors of motors and compressors | Non-oriented silicon steel | Flux rotates through every direction of the lamination |
| Large hydro-generator and wind generator sets | Non-oriented silicon steel | Large laminations punched in all directions, uniform properties needed |
| Small instrument transformers and low-duty equipment | Either, by cost target | Loss savings must justify the premium of oriented material |
Because of this split, the same product is known by two familiar names: cold-rolled non-oriented silicon steel sheet is often called cold-rolled motor silicon steel, while cold-rolled oriented silicon steel strip is called cold-rolled transformer silicon steel.
Choosing and Specifying Correctly
Both families are purchased against defined standards: GB/T 2521.1 and IEC 60404-8-7 or EN 10107 for oriented grades, and GB/T 2521.2, IEC 60404-8-4 or EN 10106 for non-oriented grades.
Grade designations encode thickness and guaranteed maximum loss. A non-oriented grade such as 50W600 means 0.50 mm strip with a maximum loss of 6.00 W/kg at 1.5 T and 50 Hz; an oriented grade such as 27Q110 means 0.27 mm strip with a maximum loss of 1.10 W/kg at 1.7 T and 50 Hz.
The specification must state measured frequency and polarisation, because loss values quoted at different test conditions cannot be compared directly.
Lamination orientation, burr height, flatness, coating type and stacking factor all affect the final core loss and should be agreed before production, not after.
Frequently Asked Questions
Q: Are non-oriented and oriented silicon steel sheets the same material?
They belong to the same iron-silicon family and come from similar melting and rolling equipment, but they differ in silicon content, texture control and magnetic directionality, so they are not interchangeable.
Q: Which sheet has the lower iron loss?
Because oriented strip is measured at a higher polarisation and still gives a lower loss figure, it is the lowest-loss product of the two when the flux runs along the rolling direction.
Q: Can oriented silicon steel be used in a motor?
Only in special designs. The flux in a normal stator rotates through all directions, so the directional advantage is lost and the extra cost is not recovered.
Q: Why is carbon controlled so carefully in both sheets?
Carbon in solid solution increases hysteresis loss and promotes magnetic ageing. In oriented grades carbon also has to stay high enough during rolling for the inhibitor to work, then be removed in decarburisation annealing.
Q: What does the insulating coating do?
It raises inter-laminar resistance so that eddy currents cannot circulate between laminations, and in oriented grades it adds tensile stress that lowers loss. Coating quality directly affects measured core loss.
Q: Does a thinner sheet always reduce loss?
Thinner sheet reduces eddy-current loss at a given frequency, but it also increases the number of laminations and the cost of punching and stacking, so the optimum thickness depends on frequency and on the duty cycle of the machine.







