ASME SA213 TP321 Bright Annealed Tube for High Temperature Food and Pharmaceutical Service
Leave a message
What ASME SA213 Covers
ASME SA213 is the specification for seamless ferritic and austenitic alloy steel boiler, superheater and heat exchanger tubes. It is the section of the ASME boiler and pressure vessel code family that buyers cite when a tube must carry a fluid at pressure and temperature inside a fired or unfired heat transfer unit. Because the specification is written around seamless product, the chemical composition, tensile requirements and surface condition clauses all assume a tube produced without a welded seam.
TP321 is one of the austenitic grades listed in that specification. It is a titanium stabilised 18-8 type stainless steel, and the titanium addition is the reason the grade behaves differently from plain 304 or 316 in the temperature range where chromium carbides would otherwise precipitate at the grain boundaries.
What a TP321 Bright Annealed Tube Is
A TP321 bright annealed tube is a seamless austenitic stainless steel tube manufactured to SA213, then heat treated in a controlled atmosphere so that the surface emerges free of oxide scale and free of decarburisation. Instead of the dull, scaled or pickled surface left by conventional processing, the tube leaves the furnace with a clean, bright finish and a coherent chromium rich passive film already in place.
Three practical consequences follow. First, the passive film is uniform because it formed in a clean furnace atmosphere rather than being reconstructed after acid pickling. Second, the surface is smooth and free of the roughness and residue that trap product in food, dairy and pharmaceutical piping. Third, the bore of a bright annealed tube is far easier to clean and to verify as clean, which is why the finish is common in hygienic and high purity service as well as in semiconductor and instrumentation tubing.
The titanium content does the metallurgical work. Titanium has a stronger affinity for carbon than chromium does, so it forms stable titanium carbides and leaves chromium in solution, protecting the grain boundaries from sensitisation during welding and during long exposure at elevated temperature.
Why Bright Annealing Suits Food and Pharmaceutical Service
High cleanliness: a smooth, low roughness surface resists adhesion of product, biofilm and residue, which supports repeatable cleaning and sterilisation cycles.
Contamination control: a scale free bore eliminates the oxide particles and embedded debris that a mechanical or pickled finish can release into a process stream.
Corrosion uniformity: the passive film forms under controlled conditions, so corrosion resistance is consistent around the circumference and along the length of the tube.
Temperature capability: the titanium stabilisation allows the grade to be used in equipment that is hot cleaned or steam sterilised without the intergranular attack that affects unstabilised grades.
Inspection friendliness: a bright, uniform surface makes visual, borescope and dye penetrant inspection of the bore more reliable.
For these duties the tube is normally specified with a maximum surface roughness of Ra 0.4 µm or finer, and with an internal and external finish that is agreed between the mill and the purchaser at the ordering stage.
Chemical Composition of TP321
Heat analysis is performed to the limits of the specification, and the titanium requirement is expressed as a multiple of the carbon plus nitrogen content rather than as a single value.
| Element | Requirement, % | Element | Requirement, % |
| Carbon | 0.08 max | Chromium | 17.00 - 19.00 |
| Manganese | 2.00 max | Nickel | 9.00 - 12.00 |
| Silicon | 1.00 max | Nitrogen | 0.10 max |
| Phosphorus | 0.045 max | Titanium | 5 x (C + N) min to 0.70 max |
| Sulphur | 0.030 max | Molybdenum | Not specified for this grade |
The titanium range is the point most often misread. A minimum of five times the combined carbon and nitrogen content is required to tie up the carbon fully, and 0.70 % is the ceiling, so a heat with high carbon needs more titanium than a low carbon heat while staying under the maximum.
Mechanical Properties at Room Temperature
The specification sets minimum tensile properties for the finished tube rather than for the strip or billet from which it was made.
| Property | Requirement |
| Tensile strength | 515 MPa minimum |
| Yield strength, 0.2 % proof | 205 MPa minimum |
| Elongation in 50 mm gauge length | 40 % minimum |
| Hardness, Rockwell B | 95 HRB maximum |
| Hardness, Brinell | 217 HB maximum |
Typical physical values used in thermal design are a density of about 8027 kg/m3 and an elastic modulus of about 193 GPa. Mean coefficient of thermal expansion is roughly 16.6 µm/m per degree Celsius over the range from 0 to 100 Celsius, 17.2 over 0 to 315 Celsius and 18.6 over 0 to 538 Celsius. Thermal conductivity is approximately 16.1 W/m·K at 100 Celsius and 22.2 W/m·K at 500 Celsius, with a specific heat of about 500 J/kg·K at room temperature and an electrical resistivity of about 720 nΩ·m.
Grade Equivalents, Size Range and Surface Condition
| Standard system | Designation |
| United States, UNS | S32100 |
| European, EN number and name | 1.4541, X6CrNiTi18-10 |
| Japan, JIS | SUS 321 |
| United Kingdom, old BS designation | 321S31 |
Bright annealed SA213 TP321 tube is commonly produced with outside diameters from 12.7 mm to 114.3 mm and wall thicknesses from 0.89 mm to 6.0 mm, with intermediate sizes available on request. Because TP321 is an austenitic grade, the tube is supplied either cold finished and bright annealed or hot finished and then finished to the agreed surface condition. Cold finished tube must be free of scale and suitable for inspection, and light surface oxidation is not treated as scale. Where the tube is bright annealed, pickling is not required, and any additional surface requirement is settled between supplier and purchaser before the order is released.
Typical Applications and Testing
Boiler superheater and reheater tubes in power generation, including small hydro and thermal plant auxiliaries.
Economiser tube bundles and auxiliary steam generator tube bundles.
U-tube heat exchangers for chemical, petrochemical and refinery service.
Hydrogenation reactor feed and discharge lines and other high temperature process piping.
High temperature molten salt heat exchangers in concentrated solar thermal plants.
Hygienic process lines for food, dairy and pharmaceutical production where cleanability governs material selection.
Tubes are supplied after hydrostatic or eddy current testing, and intergranular corrosion testing is normally added for welded assemblies and for service where sensitisation is a risk. Dimensional checks cover outside diameter, wall thickness, ovality and length, and the mill test certificate should identify the heat number, the mechanical results and the non destructive test methods that were applied.
FAQ
Q: What is the difference between an SA213 TP321 bright annealed tube and a pickled tube?
Both are SA213 TP321, but the bright annealed tube leaves the furnace with a scale free surface and a uniformly formed passive film, while a pickled tube has a rougher matte finish produced by acid removal of oxide.
Q: Why is titanium added to the 321 grade?
Titanium preferentially combines with carbon, keeping chromium in solution and preventing chromium carbide precipitation at grain boundaries, which protects the tube from intergranular corrosion after welding or long high temperature exposure.
Q: In which applications should bright annealing be specified rather than pickling?
Choose bright annealing where cleanliness, low surface roughness or corrosion performance drives the design, such as food, dairy, pharmaceutical, semiconductor and high purity instrumentation tubing.
Q: What size range is practical for SA213 TP321 tube?
Bright annealed TP321 is regularly produced with outside diameters from 12.7 mm to 114.3 mm and walls from 0.89 mm to 6.0 mm, with other combinations available by agreement.
Q: What documentation should come with the delivery?
A mill test certificate showing heat analysis, tensile results, hardness, surface condition and the non destructive testing performed, plus dimensional records for outside diameter, wall thickness and length.
Q: Does bright annealing remove the need for pickling after fabrication?
The delivered tube does not require pickling, but welds and heat affected zones created during fabrication still need cleaning and passivation so that corrosion resistance is restored across the joint.







